Double Glazing Door Lock Repairs
Have your uPVC window or door mechanism deteriorated? Maybe the handles on your uPVC windows and doors aren't aligned properly or are difficult to use.
You will lose energy when your double-glazed doors do not work properly. This can also increase the likelihood of burglaries. Owen the Locksmith can repair your door lock at a reasonable cost.
Snapped Key
It can be quite frustrating when a key is snapped inside the lock. This can also be a security risk in that it can leave you vulnerable to a burglar if the door is not locked. Fortunately, there are quick fixes you can attempt to fix the issue and get your door functioning correctly.
Be sure to remain calm. If you panic you could end up pushing the broken key piece further into the lock.
Next spray WD-40 or another penetrating oil into the lock to aid in making the broken piece slip out more easily. You can also use a screwdriver to break off any pieces stuck. If you're fortunate enough to have a bit of the key that is sticking out it, you can make use of a paperclip, or any other metal object that is thin to grab it and pull it out. Both methods work, but be careful not to push the broken key piece further into the keyway.
Some paperclips have grooved edges that could be used as a hook extractor and Jigsaw blades also work for this use. If you don't happen to have one of these tools, you can bend a hook using needle-nosed pliers. Finally, you can use a pair of tweezers grab and remove the last bit of the broken keys.
If you are unable remove the broken piece of key then you can use a lock deicer. It is available in most hardware stores and works by freezing any moisture that may be present in the lock.
If none of these solutions seem to work, it might be time to contact a locksmith. The experts at Fitlocks can quickly fix problems with uPVC door locks and mechanisms such as snapped keys and broken handles. They can also reconfigure the double glazing door mechanisms so that they are easier to use. You can schedule repairs to your double-glazing online or contact us to discuss your needs.
Broken Cylinder
A broken cylinder can be a serious security risk. Luckily, it's an easy repair for an expert locksmith to complete. To repair the cylinder, locksmiths must tap it. They can do this with a hammer or other tool, but the most efficient way is to make use of a long match or piece of wire. Position the match or the wire's end in the keyway. The locksmith will strike the lock and break it open. This is far better than using a hammer, which could damage the lock.
The most common cause of cracks in the cylinder head is overheating. This can happen when the cylinder block as well as the cylinder head are made from different metals, including cast iron and aluminum. Different metals will be heated and cool at different rates. This could cause localized hotspots to expand more quickly than the rest of the cylinder.
Another reason that could cause cylinder cracks is corrosion. If the cylinder head and the block of the cylinder are not properly maintained, this can result in corrosion or rust that could cause them to expand at a greater rates than they ought to. This can lead to cracks in the future.
If your uPVC window or door lock is stiff and requires more pressure to turn it could be due to a variety reasons. A malfunctioning locking mechanism, misalignment or the wear of the handle are typical causes of this issue.
This is a straightforward and cost-effective fix that a majority of double glazing owners can do. A professional locksmith can usually solve the issue within one hour of arriving at the property. They can repair the locking mechanisms, or change the window handles and replace the gearboxes, based on your specific needs. A professional locksmith will always be able to advise you on the most cost-effective options for your home. They can even recommend upgrades to high-security 3 Star TS007 euro cylinders that will give you an additional layer of protection against burglars. This is a small price to pay for the security that comes with knowing your uPVC doors are safe.
Broken Handle
It's not surprising that window handle locks could break. They are equipped with complex mechanisms that become less effective over time. If yours is damaged it's difficult to determine the source of the issue and make sure you fix it correctly.
Fixing your broken handle, whether it's the internal latch or locking mechanism, will improve the security of your uPVC door and prevent draughts. When you aren't doing it right, replacing or repairing the handle could be costly and may cause damage to the door's frame and lock, so it's worth taking some time to make sure you do it correctly.
With the window in the open position then loosen the screw that holds the handle by using the screwdriver. The screw should be on the inside of the backplate, which is usually hidden by a screw cap for aesthetic reasons. You should not be able to replace any internal parts of the handle such as the plates and levers on either side. Ideally, keep them in the same order so that you double glazing company near me can re-install them if needed.
Next, turn the handle so it's at 90 degrees to the window frame. Finally, loosen the screw at the back of the handle that fixes it to the internal spindle with another screwdriver. Once the screw is loose, pull the handle out and take the broken spindle out. Replace it with a brand new spindle, making sure it's the same length (you can purchase them online or in hardware stores). Securely screw it into the correct position. Be careful not to tighten too much because this could cause damage to the handle or the window frame.
Close the handle and try it. Hopefully, it will work smoothly and you'll be able to open your window again.
Be sure to double-check that your uPVC window is closing properly when you're working with the handle. If they're not closing properly cause damp and draughts inside your home as well as compromising the energy efficiency of click here your home. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they shut correctly.
Broken Spindle
It is often the case that the spindle within a handle breaks rather than the handle itself. This is most typical in uPVC tilt and turn windows. These windows require a handle that operates an locking device within the window frame. The handle is connected to a rod in the centre that in turn activates mushroom-like locking cams, these lock into window frame keeps. If the dead latch mechanism fails to open when the handle is turned it is possible that the spindle is broken and this could be a frustrating problem.
There are ways to fix this issue. A good locksmith can quickly and efficiently fix this problem. They will be able to take apart the window handle using a tool that removes the wheel portion of the mechanism, where the spindle is. This can be done with no damage to the handle or the window frame.
After removing the wheel, the technician can examine the spindle and determine what caused it to break. This involves disassembling the spindle, and then examining each component part, noting any damage or excessive wear. This procedure is typically carried out by technicians working in a clean and safe environment.
The next step is to clean the damaged spindle, this helps eliminate any dirt or debris that might be obstructing its normal functioning. Following this, the spindle can be repaired or replaced. If the technician is replacing the double glazing repairs near me spindle, it is possible to use a dowel that is the same size to the original. He will then make holes in the same way into both pieces. This will ensure that the spindle will fit perfectly with the handle.
If the damaged spindle can't be repaired it may require replacement completely. Home centers sell generic click here replacements however if your window style is rare then you'll have to speak with an expert in woodworking or cabinet making click here who can make the exact component. After the spindle is installed, it can be attached to the handle. Place the screw holes on the handle with the screws that are already in the frame. Once the handle is securely seated, you can operate your uPVC windows.